1. A Real Price-Comparison Scenario
Three quotations on the table, all 500 litres, prices 20 % apart.
- Supplier A's 500 L corresponds to roughly 560 litres of geometric vessel volume;
- Supplier B's 500 L corresponds to roughly 520 litres of geometric volume;
- Supplier C's 500 L means "you can charge 500 litres of material per batch".
Reading A, B, C in order, you conclude the price rises toward the end. But ranked by "how much material each batch actually processes", the order may reverse completely — because C is talking about charge volume, while A's 560 litres is geometric volume, and after applying a fill factor A may only take 360 litres per batch.
That is what makes the word "volume" dangerous: it has three meanings, and all three are defensible.
2. The Three Volumes
| Concept | Definition | How obtained | Where used |
|---|---|---|---|
| Total volume (geometric) | Geometric internal volume of the vessel, usually including head space, not deducting blade displacement | Calculated from drawings, or measured by filling with water | Manufacturing, strength calculation, transport dimensions |
| Nominal volume | The number in the model designation (e.g. "500 L kneader") | Generally a rounded nominal figure | Quotations, contracts, model labelling |
| Working volume (effective charge) | How much material can actually go in per batch | Total volume × fill factor | Capacity planning, batch counting, unit cost |
2.1 How they relate
Working volume = total volume × fill factor Nominal volume ≈ the model name, and need not equal either of the above
The fill factor is the key. In high-viscosity kneading systems it usually sits between 0.6 and 0.7. Below that range the blade cannot grip the material and mixing efficiency collapses; above it, material is squeezed onto the cover and sealing surfaces, head space for vacuum is insufficient, and blade torque exceeds design limits.
2.2 Why "nominal" is the least reliable
Because it is a model name — made for people to read, not for calculation.
For the same "500 L", one manufacturer rounds the geometric volume to 500, another defines the effective charge as 500, and a third simply names the machine after the nearest round number. Three "500 L" labels may sit behind 500, 560 or 520 litres of geometric volume — or behind 325, 364 or 500 litres of charge.
So on seeing "500 L", the first reaction should be: which one do you mean?
3. How Big Is the Gap: A Real Set of Relationships
Below is the correspondence between nominal and total volume on machines of the same series, listed by capacity class (specific model numbers omitted):
| Capacity class | Nominal | Total volume | Deviation |
|---|---|---|---|
| Small | 5 L | 6 L | +20% |
| Small | 10 L | 16 L | +60% |
| Medium | 50 L | 55 L | +10% |
| Medium | 100 L | 120 L | +20% |
| Medium-large | 300 L | 320 L | +6.7% |
| Large | 500 L | 560 L | +12% |
| Large | 2000 L | 2100 L | +5% |
3.1 Three conclusions to draw from the table
(1) The deviation is not a constant — you cannot back-calculate with a fixed coefficient.
Many people work on "nominal × 1.1 = total volume". The table rules that out immediately: the low is 5 %, the high is 60 %.
(2) Small machines deviate more.
From 5 L to 100 L the deviation runs 10–60 %; above 300 L it falls to 5–12 %. The reason is structural proportion: on small vessels, heads, flanges, charging ports and blade displacement occupy a far larger share of internal volume than on large ones.
(3) The same manufacturer can use different bases for different structures.
The 10 L unit above is a vertical design (vessel about 16 L by diameter × height), while the 5 L unit is horizontal (total volume about 6 L). On the vertical machine the nominal figure is closer to working volume; on the horizontal machine it is closer to total volume.
This matters: change the machine architecture and the meaning of "nominal" can change with it. Comparing across architectures or manufacturers using nominal figures alone will almost certainly misalign.
4. How This Difference Turns into Money
4.1 Spread over capacity
Take two "500 L" machines, one with 560 L of vessel volume and one with 520 L, both at a fill factor of 0.65:
| Vessel | Fill factor | Charge per batch | |
|---|---|---|---|
| A | 560 L | 0.65 | 364 L |
| B | 520 L | 0.65 | 338 L |
A difference of 26 L per batch, about 7.7 %. If both are quoted at the same price, A's real unit cost is 7.7 % lower; if A costs 5 % more, it is still the better buy.
That is why "looking only at the total price" gets the arithmetic wrong — you are comparing machine prices when you should be comparing price per litre of effective charge.
4.2 But bigger is not automatically better
The reverse must be said too: chasing a larger total volume is a common form of over-design.
Take the fill factor too high and three things happen:
- Material is pushed onto the cover and sealing surfaces — at best contaminating the seal, at worst compromising vacuum;
- Head space for vacuum is insufficient — too little gas volume means vacuum will not pull down and deaeration takes longer;
- Blade torque exceeds limits — the resistance torque of a full charge of high-viscosity material can exceed design values and trip overload protection.
So the right question is not "whose vessel is bigger" but "which configuration's effective charge per batch best matches my batch-count requirement".
5. Fill Factor: The Fourth Variable Nobody Mentions
Three volumes have been discussed. In practice a fourth variable decides how much capacity you actually get — the fill factor.
5.1 Typical range
| Material viscosity | Fill factor reference |
|---|---|
| High viscosity (paste, gel) | 0.6 – 0.7 |
| Medium viscosity | Around 0.7 or higher |
| Special processes (large gas volume required) | Lower still |
The actual value must be established by material trial. Change the material on the same machine and the optimum fill factor changes too.
5.2 A worked example
Requirement: 5 t/day, bulk density 1.2, four batches per day.
Charge per batch = 5 ÷ 1.2 ÷ 4 = 1.04 m³ = 1040 L Required total volume = 1040 ÷ 0.65 ≈ 1600 L
Note the denominator is the fill factor, not 1. Take 1040 L and match it directly against a "nominal volume" and you will select a machine that cannot actually hold 1040 L.
This is the same logic as the "23 parameters for customizing a kneader" article — that one covers which parameters to supply, this one covers which volume basis the calculated result should be matched against.
6. Five Questions That Must Be Asked
With any quotation in hand, ask these five and the basis is aligned:
| # | Ask | Why it is essential |
|---|---|---|
| 1 | "Is your 500 L nominal, total volume, or effective charge?" | Locks the basis in one sentence |
| 2 | "What are the internal geometric dimensions of the vessel?" | With diameter × height (or L × W × H) you can calculate it yourself |
| 3 | "What fill factor do you recommend, and what charge per batch does that give?" | Converts volume into capacity |
| 4 | "Is that figure volume or weight? What density are you assuming?" | Mixing volume and weight is a common source of error |
| 5 | "Is the vessel jacketed? Does any internal heat-exchange structure occupy volume?" | An external jacket does not occupy internal volume; internal structures do |
6.1 How to verify question 2 yourself
For a cylindrical vessel:
V = π × (D/2)² × H
A W-shaped horizontal vessel will not fit the cylinder formula, but the water-fill method works: ask the manufacturer to fill the empty vessel with water and meter how many litres go in. Crude, but the most reliable check — and a legitimate manufacturer will not refuse.
6.2 A detail that is easily missed
Does total volume include the volume displaced by the blades?
Strictly, geometric total volume does not deduct blade volume, whereas the material you can actually charge occupies the space left after the blades take their share. So "total volume × fill factor" is itself an engineering approximation — the fill factor implicitly covers blade displacement, gas space and turnover allowance.
This also explains why different blade types (sigma, Z, planetary) carry different recommended fill factors: they displace different volumes.
7. Conclusion
Back to the opening scenario.
Three suppliers quote 500 L, prices 20 % apart. The productive move is not to negotiate, but to establish the basis first:
Nominal? Total volume? Or effective charge?
These three can differ by 5 % to 60 %, and the deviation is neither constant nor uniform across structures. Under those conditions, any "price per nominal litre" comparison is a comparison of three different machines.
In one line:
Compare the basis, not the number.
Pin down the volume basis and capacity can be calculated; pin down the fill factor and quotations become comparable.
If you are in the middle of a comparison, the cheapest thing you can do is send those five questions to every supplier and ask each to answer on the same basis. A manufacturer willing to answer all five carefully is usually one that has actually built these machines.

