1. Three Methods, Three Intervals
The procedure states three things:
| Method | Interval | Location |
|---|---|---|
| Drip-feed | At least twice per shift | Exposed moving parts needing continuous replenishment |
| Grease injection | Once every 20 days | Enclosed points such as bearings |
| Oil bath | Replaced every 3 months | Gearbox and other oil-bath locations |
1.1 Why the intervals differ so widely
The intervals span two orders of magnitude (twice per shift versus once every three months) because they do not solve the same problem:
| Method | Nature | Failure mode |
|---|---|---|
| Drip-feed | Replenish consumption | Oil runs out and is not replaced → dry friction |
| Grease injection | Maintain inventory | Grease ages and migrates → insufficient lubrication |
| Oil bath | Complete fluid change | Oil degrades, contaminants accumulate → lubrication and cooling both fall |
Drip-feed is a consumable; the oil bath is a system. Forget the first and you have consequences within hours; forget the second and it shows in months — by which time it is usually wear.
1.2 Mixing them up is the common error
Three confusions recur on the floor:
- Treating the oil bath as "top it up". Level drops, new oil goes in, old oil never comes out — contaminants and oxidation products stay indefinitely.
- Using one oil everywhere. Drip points, bearings and gearboxes need completely different viscosities and additive packages.
- "More grease is safer". See Section 6.
2. Oil Bath Change: More Than Draining
Draining oil has two layers of value. The second is usually wasted.
2.1 Layer one: remove degraded oil
Oil oxidises, absorbs water, carbonises and picks up wear debris in service. Past a point, both lubricity and cooling capacity fall — and on a kneader these compound: the gearbox already works at low speed and high torque; add poorer cooling and oil temperature climbs.
2.2 Layer two: read the oil that comes out (a free diagnosis)
This is the most wasted diagnostic opportunity on the machine.
Drain while hot, catch the oil in a light-coloured container, let it settle, then look at three things:
| What you see | What it suggests |
|---|---|
| Bright metal flakes, plate-like pieces | Gear tooth spalling, bearing race spalling |
| Fine uniform metallic powder (grey, metallic sheen) | Normal running-in wear (common in the first few changes on a new machine) |
| Copper-coloured particles | Cage, bronze worm wheel or bush wear |
| Milky / cloudy | Water ingress (coolant leak or condensation) |
| Black, viscous, burnt smell | Prolonged high temperature; oil already degraded |
Metal powder in the first change on a new machine is normal; from the second change it should drop noticeably. If it is still heavy at the second and third change, that is a wear problem, not running-in.
2.3 The correct sequence
Drain while hot → clear bottom sludge → (if needed) flush → refill to mark → recheck level after running
"While hot" matters: cold oil is viscous and leaves contaminants on the bottom; hot oil carries suspended matter out with it.
"Clear bottom sludge" is the step most often skipped: the drain plug is rarely at the lowest point, so a layer of sludge remains. Refill without clearing it and the new oil is contaminated immediately.
3. End-Plate Shaft Seal: Adjust First, Replace Second
The procedure is precise about this:
The end-plate shaft seal should be appropriately adjusted or replaced according to wear.
Note the order — adjust first, replace second.
3.1 Why adjustment works
Packing-type seals (PTFE packing, for example) derive sealing force from the gland compressing the packing. As it wears, packing volume drops slightly, and moderate re-tightening of the gland restores the seal without immediate replacement.
So the correct sequence is:
- Leak appears → check whether the gland can still be tightened;
- Still leaking after tightening → top up or replace the packing;
- Still leaking after replacement → check shaft alignment and surface finish.
Jumping straight to "replace" costs a shutdown and a strip-down — and if the root cause is a worn shaft, the new packing fails too.
3.2 Two things cannot wait
| Situation | Why it cannot wait |
|---|---|
| Packing wear particles entering the product | For light-coloured or translucent compound this means scrapping the batch |
| Material leaking at the end-plate seal | Leakage means product loss and a seal that has already failed |
The procedure states separately: "there must be no material leakage at the end-plate seal" — the weight of that sentence is heavier than "check periodically", because it says "must be none", not "minimise".
4. The Six-Month Inspection: What to Cover
The procedure: the machine should be inspected every six months, with wear parts checked and repaired or replaced as appropriate.
The six-month interval matters because it is earlier than "fix it when it breaks" and more thorough than "look at it daily". It suits work that requires opening up and measuring but cannot wait for a major overhaul.
| Check | How | Judgement |
|---|---|---|
| Blade-to-wall clearance | Feeler gauge at root, middle and tip | Compare with baseline; noticeable growth needs action |
| Seals | Strip and inspect shaft seal and cover gasket | Ageing, flattening or cracking means replace |
| Fasteners | Re-torque frame, end plate, bearing housing bolts | Torque to specification |
| Piping and joints | Visual and wipe test | No leakage permitted |
| Hydraulic oil and filter | Oil condition, filter differential | Cloudy or black oil means change; filter on schedule |
| Safety devices | Safety switches, limit switches, thermal elements | Test each by actuation |
| Electrical control | Terminal tightness, insulation, instrument readings | Compare against reference values |
Clearance measurement and safety device testing are the two that cannot be skipped. The first is performance; the second is safety.
5. A Printable Schedule
| Interval | Item | Key point |
|---|---|---|
| Every shift (≥2×) | Drip-feed lubrication points | Every point, none missed |
| Every shift | Check piping and joints for leakage | Visual plus wipe |
| Daily | Hydraulic oil level and temperature | Top up if low; investigate cooling if high |
| Every 20 days | Grease injection points | Metered amount; do not overfill |
| Monthly | End-plate seal leakage, cover gasket | Adjust before replacing |
| Every 3 months | Oil bath change | Drain hot, clear sludge, inspect for metal |
| Every 6 months | Full inspection (Section 4) | Clearance measurement plus safety device testing |
| Idle over 1 week | Clean, protect against corrosion, close valves | Keep relief valve and gauge reliable |
6. Three Common Mistakes
6.1 Topping up without ever draining
Level drops, oil is added, old oil never leaves. Contaminants and oxidation products accumulate, and the oil's actual condition is far worse than its appearance.
How to check: put a drop on filter paper and look at the diffusion rings. A black centre with a sharp yellow outer ring indicates degradation.
6.2 One oil for everything
Drip points, bearing lubrication and the gearbox oil bath need different viscosities and additives. The wrong oil does not fail immediately, but it shortens life — and attribution becomes very hard.
At minimum: buy the grades specified in the manual. Do not substitute "general-purpose grease".
6.3 "More grease is safer"
This is a widespread misconception. Overfilling a bearing cavity is actively harmful:
- Excess grease is churned in the cavity, generating extra heat;
- Grease conducts heat poorly, so a full cavity cools worse;
- At high temperature the grease ages and migrates faster — a worsening cycle.
Practical approach: fill the cavity to about one third to one half, not packed full; when replenishing, stop when a small amount of fresh grease appears at the relief port.
7. Conclusion
What characterises lubrication is this: done right there is no feedback, and done wrong there is no immediate feedback either.
That is why it degrades so easily into "do it when you remember". The three intervals exist precisely to prevent that degradation:
| Interval | What it guards against |
|---|---|
| Twice per shift | Dry friction (fails within hours) |
| Every 20 days | Grease ageing and migration (shows in weeks) |
| Every 3 months | Oil degradation and contaminant build-up (shows in months) |
| Every 6 months | Progressive wear and safety device failure (shows in half a year) |
The intervals are not formalities — they are the time scales of different failure modes.
Following them means correcting each failure mode while it can still be corrected.
One last point: look at the oil when you drain it — it is the only moment the machine volunteers where it is wearing.

